...

The M80 and M120 Sport tabs are ideal for boats with limited transom space. The unique batwing design provides 30% more lift than conventional trim tabs.Kits includes: (1) Helm control, (2) stainless steel trim tabs, (2) hydraulic actuators, (1) hydraulic power unit, all necessary wiring, tubing & hardware....

304 grade stainless steel. Transom mount.A complete Trim Plane Assembly (TPA) includes: 1 Trim Plane, 1 Hinge Plate & 1 Backing Plate (x2 for both sides of transom)....

Creates hydraulic pressure to lower and raise the trim tabs using 2 solenoid valves that lock tightly to secure the tabs in place. Power to lower and hold even the largest tabs in place. A Lexan cover provides water resistance, and the trCreatesanslucent reservoir allows fluid check at a glance. Uses automatic transmission fluid. Includes pump, sol...

Features tin-plated copper bus with stainless steel hardware. The highest amperage busbar available. Ideal for main DC negative or positive bus on larger boats. 300V AC / 48V DC maximum voltage. 545A AC / 600A DC continuous amperage rating....

Ideal for passing high current cables through hulls, decks and bulkheads where watertight or vapor proof integrity must be maintained. Feed-Through Terminals also eliminate chafing and provide strain relief for large cables. Larger terminals have a mounting face that can be gasketed or bedded to provide a watertight installation....

Industry standard BusBar features tin-plated copper bus, 1/4\" stainless steel studs and 8-32 terminal screws. Continuous rating 150 Amps AC/DC, maximum voltage 300 Volts AC, 48 Volts DC....

Great for limited space applications in electronics cabinets and under dashboards. Features tin-plated copper bus and stainless steel hardware. Continuous amperage of 100 Amps and maximum volts of 48DC / 300V AC....

A closed back design completely insulates power from the mounting surface. Each screw pair is one isolated circuit. Optional jumpers allow creation of common circuits. Tin-Plated Brass....

Combine negative and positive buses on one block. Features tin-plated copper bus and stainless steel hardware. Continuous amperage of 100 amps. Maximum 48V DC / 300V AC....

...

Combines negative and positive busses on one block, clear lexan lid snaps on to meet CG and ABYC insulation requirements. Features tin-plated copper bus and stainless steel hardware. Maximum Voltage 300V AC / 48V DC. Continuous Rating The maximum current a switch is designed to conduct for an indefinite period. 130A AC / 150A DC....

For batteries with integral marine wing nut posts. Top rotates 360 degrees to allow entry from any angle. Red/Black....

For batteries with marine adapter terminals added on. Red/Black....

For stud type connectors on alternators, starters, windlasses and other High amperage devices....

Provide electrical insulation for exposed panel backs and mechanical protection for panel backs protruding into lockers. Made of lightweight material for easy drilling for wire entrance and exit....

Protects circuit breakers from being accidentally switched on or off. Fits all single-pole A and B series breakers. Works on any brand breaker panel using standard A or B series circuit breakers. Includes mounting screws....

Allows only 1 of a pair of double-pole AC circuit to be activated at a time. Guarantees that AC power from 2 sources (power company and genset or inverter) will not be mixed. Fits all double-pole A and B series circuit breakers. Uses circuit breaker mounting screw holes and requires no special panel modification. Includes mounting screws, #6 flat h...

Clear insulating cover with label recesses for standard Blue Sea System labels. Cover insulates all conductive parts, satisfying ABYC/USCG requirements and stores spare fuses. Nickel-plated metal components and copper contact clips. Rated for 32V max, 100 amps max per block, 30 amps max per circuit. Uses AGC, MDL and all other 3AG glass fuses....

Fast short circuit response makes this the best choice to protect high amperage electronics equipment such as inverters. 20,000 Amp Interrupt Capacity (AIC) UL rated for DC applications under UL189L....

Tin-plated connector blades for corrosion resistance and visible indication of blown condition. Interrupt capacity is 1000 amps DC and 32 Volts DC maximum....

Fast-acting type fuses ideal for electronic devices. Tin-plated connector blades for corrosion resistance. Visible indication of blown condition. Maximum voltage: 32 volts DC. Interrupt capacity: 1000 Amperes DC....

Self trimming molded rubber bezel....

Double pole, magnetic-hydraulic, trip free circuit breakers. Combines switching and circuit protection into a single device. Allows for the neutral circuit on one pole and hot circuit on other pole. Both poles will trip if either pole trips. Rated for 250 Volts AC and 65 Volts DC. Includes mounting screws....

Meters with backlighting for low light conditions. Can be either surface or panel mount. (Separate 12V or 24V connection required for lighting)Ammeters: Include either an internal or external shunt as noted....

8-16 VDC Voltmeter with a 3 position switch for multiple battery banks. Full size 2-3/4\" meter....

Traditional metal panels provide DC Branch switching and circuit protection. All positive, negative, and grounding busses installed. Backlit label positions. Includes set of 30 common DC labels. For 12 or 24 Volt DC Systems....

Has 8 total circuit breaker positions, Red reverse polarity-indicating LED, and a set of 30 common AC labels, backlit label positions. This has 3, 15A A-series branch circuit breakers installed and 1 double-pole 30A AC main circuit breaker....

Features 3 total circuit breaker positions. Red reverse polarity indicating LED. All hot, neutral and safety ground buses installed, fully pre-wired. One 30A double-pole A-series circuit breaker....

AC Source Selection panels allow the boater to select between AC sources to supply powerto the AC Branch distribution system....

Easily installed in any Blue Sea Panel. Simple push-in installation mounts in any thickness material. Useful as general indicator and alarm lights. 11/64\" mounting hole size. Wire Gauge 26 AWG....

Features 5 total breaker positions, Red reverse polarity indicating LED, all hot, neutral and safety ground buses installed and fully prewired. Includes a set of 30 common AC labels. 3-15A A-series circuit breakers installed and one double-pole 30 AC, A series main circuit breaker, 0-150V AC voltmeter....

Features include waterproof panel mount fuse holders which accept commonly available AGC and MDL fuses. Made of heavy 1/8\" aluminum. Waterproof contura switches and \"On\" indicating LED\'s embedded in switch. Completely wired and ready to install. Comes with a set of 30 common DC labels....

AC Branch panels distribute current from a high amperage input into lower amperage circuits. Styled to match existing panels, the traditional metal panels are equally suited for use as extensions to existing panels or as full replacements. All panels are pre-wired and include LEDs in all positions and label backlighting. Marine grade aluminum frame...

Connects to 12-volt source via two 6\" 18 AWG wire leads....

Tough, weatherproof Lexan material. Backlightable with label backlight system. Kit 8031 includes: (Blank), Aft Cabin Lights, Aft Cabin Outlets, Air Conditioner, Air Conditioner 2, Appliances, Battery Charger, Cabin Outlets, Computer, Entertainment Center, Fwd Cabin Lights, Fwd Cabin Outlets, Galley, Galley Outlets, Heater, Inverter, Lights, Macerat...

Features 13 circuit breaker positions, ten 15A installed. 8-16 Volt voltmeter with 3 position switch for multiple battery banks. 0-50 amp ammeter with remote shunt. All positive, ground and grounding buses installed, fully pre-wired. Comes with a set of 30 common labels....

...

Features 10 total circuit breaker positions with seven 15A circuit breakers included. 8-16 volt voltmeter with 3-position switch for multiple battery banks. 0-50 amp ammeter with remote shunt. All positive, ground and grounding buses installed, fully pre-wired....

Six position circuit breaker panel with 15A circuit breakers installed. All positive, negative and grounding buses installed, fully pre-wired. Includes set of 30 common DC labels. Configure for 12 or 24V DC distribution....

For applications such as starters, bilge pumps, horns, wipers and engine controls where switching, in addition to circuit protection is required. All panel switches mount in Blue-Sea A series breaker panels. Supplied with mounting adapter for standard 5/8\" circuit breaker mounting hole. Nickel-plated brass and phenolic non-corrosive construction. ...

For applications such as starters, bilge pumps, horns, wipers and engine controls where switching, in addition to circuit protection is required. All panel switches mount in Blue-Sea A series breaker panels. Supplied with mounting adapter for standard 5/8\" circuit breaker mounting hole. Nickel-plated brass and phenolic non-corrosive construction. ...

Tough, weatherproof Lexan material. Used on all Contura waterproof breaker and fuse panels and ST blade fuse blocks. Black. Features 60 common DC labels:(Blank), 12 Volt DC, 24 Volt DC, Accessory, Aerator, Anchor Light, Auto Pilot, Bait Pump, Baitwell, Battery, Battery Charger, Bilge, Bilge Pump, Blower, Bow Light, Cabin, Cabin Lights, CB Radio, Ce...

Vibration, shock, moisture and salt spray resistant. Ignition protected, safe for use on gas powered boats. Mounts in Blue Sea Waterproof panels. LED light indicates when circuit is on. 20 Amps @ 12VDC, 15A @ 24VDC. Meets UL 1500 and ISO 8846 external ignition protection requirements. On in parenthesis (On) indicates a momentary postion....

...

...

Large, bright LED characters have 3 levels of brightness for easy monitoring of key functions in a splash-proof case. Easy to surface mount in a 2\" round hole. Face size is 2.625\" W x 1.260\" H....

Water resistant bilge pump panel is designed for open-cockpit and flybridge applications and features a contura switch with ON indicating LED\'s and a watertight mounting gasket....

24 total circuit breaker positions, 9 blank positions, 15 -15 amp circuit breakers installed. All positive, negative and grounding buses installed, fully pre-wired. Includes set of 30 common DC labels. Detailed installation instructions and cutout template. Configure for 12 or 24V DC distribution with supplied labels. Amperage: panel main bus 100A....

Designed for flybridge and open cockpit applications. Rated IP66 - \"Use on Shipdecks\". Installed switch is On/Off. Features push button circuit breakers with waterproof boot, countersunk mounting holes throughout, heavy 1/8\" aluminum material, two-part polyurethane Arctic White finish, waterproof contura switches, all components waterproof from ...

Mounts in Blue Sea waterproof panels. Legend: \"BRIGHT\" and \"DIM\". 12 VDC, 15 amps. Quick connect terminal. On in parethesis (On) indicates a momentary postion....

Hermetically sealed, waterproof, and vaporproof. Pulse circuit requires very low current draw when contact is closed....

Allows creation of common circuits on independent connectors. Nickel-plated brass. Continuous amperage - equivalent to matching block....

Backlit meters can either surface or panel mount. (Separate 12V or 24V connection required for lighting)Ammeters: 0-50 Amp AC scale in 5 amp increments. A 2 wire connection from a coil slips over the wire to be measuredVoltmeter: Dial marked in 5 Volt increments...

...

For sealing the finest cracks and seams. The only liquid sealant that does not shrink when cured. Flows into the smallest cracks, seams and stays. Cures to a firm bond with the same lifetime adhesion as regular Life-Calk. Seal is durable, flexible and stops seepage for good. Made from LP polysulfide polymer....

The perfect cure for dry rot and restores the strength of wood. Penetrates deep through capillary action, and completely saturates wood, arresting the progress of dry rot by encapsulating fibers. Cures into a tough and resilient mass bonding wood fibers to be stronger than the original. Ideal for wood encapsulated by fiberglass such as transoms, st...

Heavy-duty one-step powder cleaner. For teak decks and trim. Restores stained teak without sanding. Apply to wet teak and scrub with BoatLIFE\'s Scrub-All. Extra strong. Will not harm Life-Calk® or Teak Deck Sealant....

One-step bilge cleaner that breaks down oil, grease and grime in salt or fresh water. Hydrotropic formula allows oil solubility in water while cleaning and deodorizing bilges. Oil is held in suspension for easy pump out. Biodegradable, No phosphates. Non-corrosive to marine metals. Cleans bilge pumps while it works....

Designed specifically for fiberglass boats. A fast-curing (24 hours) polyurethane/silicone adhesive sealant. Permanently flexible, non shrinking. Outstanding adhesion to fiberglass, glass, plastic and wood. Fast skinning (10 minutes). Use above or below waterline. Acid-free. Non-yellowing, UV resistant....